夜夜嗨AV一区二区三区,欧洲美女熟乱av,亚洲精品无码久久久久久,蜜桃传媒一区二区亚洲AV

Dongguan Weize Hardware Co., Ltd

Elaborate production, sincere serviceFocus on the development and production of carbide rotary files 18922987188/0769-27221035

Dynamic

More

Dynamic

聯(lián)系我們

Mr. Lin: 18922987188

Landline: 0769-27221035

Fax: 0769-28055429

Email: sales1@wizzardtools.com

Address: Building 1, Wansheng Science and 

Technology Park, No. 15, Qinghua Road, Nancheng 

Street, Dongguan City, Guangdong Province

What are the causes and mitigation measures of tool wear?

Time: 2021-12-30 16:57:30  View: 1059

Abrasives wear hard spots such as carbides, oxides, nitrides and debris in the workpiece material, which draw grooves on the tool surface, resulting in tool wear. Its wear strength (i.e. wear speed) depends on the hardness difference between the hard point and the tool. The measures to reduce wear can be heat treatment to reduce and soften the hard points contained in the workpiece material, or select the tool material with high hardness and fine grain. Abrasive wear is often the main reason for the wear of low-speed cutting tools.

Bonding wear due to the bonding (cold welding) phenomenon at the knife chip interface, when the bonding part flows and separates along the front with the chip, if the bonding strength is low, it will shear and separate along the bonding surface; If the bond strength is high, the shear occurs outside the joint surface. Generally, most of the shear occurs in the chip bottom layer. However, due to the microstructure defects of the tool material, or due to high-temperature softening, fatigue and other reasons, the shear may also occur in the surface layer of the tool material, resulting in the particles on the surface layer of the tool being torn away. When the particle size is small, it is called bonding wear, and when the particle size is large, it is called spalling. The appearance feature of bonded wear surface is rough surface. The influencing factors of bond wear are complex. The strength ratio of the contact area between tool material and workpiece material affects the bonding wear strength to a great extent, and their hardness ratio sometimes has a decisive influence. The tear strength of hundreds of small particles is quite related to the tear strength of more particles. The higher the hardness of the tool, the finer the grains and the smaller the size of the falling particles. Increasing the stiffness of the system and reducing the vibration will help to avoid the falling off of large particles.

3-diffusion wear two metals in contact with each other. Due to the concentration difference of chemical components, the atoms at the interface will diffuse each other,

However, the diffusion is very slow at room temperature and can be increased thousands of times at high temperature. In high-speed cutting, the contact area between the tool and the chip and the machining surface has high temperature, high pressure, strong adhesion and large plastic deformation. Some elements (iron, carbon, cobalt and tungsten) diffuse faster, which changes the chemical composition and microstructure of the metal on the surface of the tool, reduces the strength and increases the brittleness, thus aggravating the wear of the tool. The tool surface quotient of diffusion wear is almost as smooth as polishing. For cemented carbide tools, Co, C and W in the tool surface diffuse to the workpiece material, II; Fe in the part material diffuses to the tool, decarburizes and depleted tungsten on the surface of the tool, and generates intermediate compounds with low strength and high brittleness, which aggravates the wear of the tool. Because the bonding of tic is stronger than that of WC, YT cemented carbide has strong diffusion wear resistance. Diffusion wear is a phenomenon occurring at high temperature. Its main influencing factors are the chemical properties, relative moving speed and temperature of tool materials. The chemical properties of the combination of tool materials and workpiece materials have a greater impact than the mechanical properties, but the temperature plays a decisive role. YG alloy diffuses obviously at about 800 ° C and YT alloy at about 1000 ° C. after that, the diffusion rate increases by one time for every 20 ° C increase in temperature. The measure to reduce tool wear is to reasonably select the tool material to make it have good chemical stability combined with the workpiece material; Reasonably select cutting parameters and reduce cutting temperature. It should also be mentioned that when the temperature increases from low to high, the bonding wear does not always increase. Each combination of tool material and workpiece material has an optimal cutting temperature.

4. Chemical wear at a certain cutting temperature, the tool material reacts with some elements in the surrounding medium or cutting fluid to form compounds to accelerate tool wear, which is called chemical wear. For example, oxygen in the air and chlorine and sulfur in extreme pressure cutting fluid react with tool materials to accelerate tool wear.

In addition to the above four causes of tool wear, there are also fatigue damage and thermoelectric wear. The above four reasons can be divided into two categories. Abrasive wear and bonding wear belong to mechanical wear. They exist under various cutting conditions and are the basic cause of tool wear, but they are often the main cause of tool wear in low speed cutting.

Diffusion wear and chemical wear belong to thermal wear, which is the reason for tool accelerated wear, that is, the main reason for tool wear in high-speed cutting. However, there is no strict boundary between them, and they affect each other. Under certain cutting conditions, some wear may play a leading role. The measures to reduce wear and tear also need to find out the main causes according to the specific situation in order to suit the remedy to the case. However, cutting temperature or cutting speed closely related to it has a decisive effect on wear. Figure 3-27 shows the relationship between various wear strength ratios and cutting speed.


九九精品99久久久香蕉| 加班被蹂躏的人妻在线| 成在线人免费视频一区二区| 国产野战无套av毛片| 久久国产成人精品av| 久久久人人人婷婷色东京热| 国内老熟妇对白xxxxhd| 亚洲人成亚洲精品| 少妇人妻互换不带套| 高潮小受站不住了GAY片| 亚洲国产成人精品无码区一本| 97免费人妻无码视频| 亚洲精品成人片在线观看| 中文字幕无码不卡一区二区三区| 国产视频一区二区| 日本55丰满熟妇厨房伦| 国产成人午夜福利院| 亚洲国产精品无码专区成人| 欧美 国产 综合 欧美 视频| 亚洲欧美日韩在线观看一区二区三区 | 国产成本人片无码免费2020| 99久久久国产精品免费蜜臀| 国模小黎自慰gogo人体| 久久精品成人无码观看免费| 桃子视频在线播放WWW| 毛片内射久久久一区| 精品亚洲欧美无人区乱码| 欧日韩无套内射变态| a网站在线观看| AV人摸人人人澡人人超碰妓女| 国产欧美精品亚洲日本一区| 久久欧美与黑人双交男男| 国内精品久久久久久中文字幕| 在线天堂新版最新版在线8| 狠狠躁夜夜躁人人爽天天5| 新狼窝色av性久久久久久| 免费特级毛片| 2020国产成人精品视频| 亚洲精品国产精品乱码不卡| 国产男女乱婬真视频免费| 夜鲁鲁鲁夜夜综合视频欧美 |